=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD40EFRX-68N32N0
Serial Number:
LU WWN Device Id:
Firmware Version: 82.00A82
User Capacity: 4 000 787 030 016 bytes [4,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jun 27 23:44:32 2019
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (43680) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 463) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 197 163 021 - 5116
4 Start_Stop_Count -O--CK 097 097 000 - 3387
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 094 094 000 - 4699
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 097 097 000 - 3261
192 Power-Off_Retract_Count -O--CK 200 200 000 - 115
193 Load_Cycle_Count -O--CK 199 199 000 - 4513
194 Temperature_Celsius -O---K 118 114 000 - 32
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 56 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 9
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 9 [8] occurred at disk power-on lifetime: 3793 hours (158 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 0b 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 a0 00 00:00:04.099 SMART READ LOG
2f 00 00 00 01 00 00 00 00 00 e1 e0 00 00:00:04.099 READ LOG EXT
b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 00:00:04.098 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 a0 00 00:00:04.098 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 a0 00 00:00:04.097 SMART READ LOG
Error 8 [7] occurred at disk power-on lifetime: 2562 hours (106 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 0b 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 a0 00 00:46:03.832 SMART READ LOG
2f 00 00 00 01 00 00 00 00 00 e1 e0 00 00:46:03.832 READ LOG EXT
b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 00:46:03.832 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 a0 00 00:46:03.831 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 a0 00 00:46:03.831 SMART READ LOG
Error 7 [6] occurred at disk power-on lifetime: 2171 hours (90 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 0b 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 a0 00 2d+06:23:44.210 SMART READ LOG
2f 00 00 00 01 00 00 00 00 00 e1 e0 00 2d+06:23:44.210 READ LOG EXT
b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 2d+06:23:44.209 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 a0 00 2d+06:23:44.209 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 a0 00 2d+06:23:44.208 SMART READ LOG
Error 6 [5] occurred at disk power-on lifetime: 1811 hours (75 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 0b 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 a0 00 03:25:06.343 SMART READ LOG
2f 00 00 00 01 00 00 00 00 00 e1 e0 00 03:25:06.343 READ LOG EXT
b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 03:25:06.342 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 a0 00 03:25:06.341 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 a0 00 03:25:06.341 SMART READ LOG
Error 5 [4] occurred at disk power-on lifetime: 1529 hours (63 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 0b 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 a0 00 07:45:26.558 SMART READ LOG
2f 00 00 00 01 00 00 00 00 00 e1 e0 00 07:45:26.557 READ LOG EXT
b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 07:45:26.557 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 a0 00 07:45:26.556 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 a0 00 07:45:26.556 SMART READ LOG
Error 4 [3] occurred at disk power-on lifetime: 1246 hours (51 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 0b 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 a0 00 01:55:19.701 SMART READ LOG
2f 00 00 00 01 00 00 00 00 00 e1 e0 00 01:55:19.701 READ LOG EXT
b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 01:55:19.701 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 a0 00 01:55:19.700 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 a0 00 01:55:19.700 SMART READ LOG
Error 3 [2] occurred at disk power-on lifetime: 1210 hours (50 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 0b 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 a0 00 05:42:48.345 SMART READ LOG
2f 00 00 00 01 00 00 00 00 00 e1 e0 00 05:42:48.345 READ LOG EXT
b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 05:42:48.345 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 a0 00 05:42:48.344 SMART READ LOG
b0 00 d5 00 01 00 00 00 c2 4f 09 a0 00 05:42:48.344 SMART READ LOG
Error 2 [1] occurred at disk power-on lifetime: 888 hours (37 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 0b 00 00 00 00 00 00 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d5 00 01 00 00 00 c2 4f e1 a0 00 02:31:30.778 SMART READ LOG
2f 00 00 00 01 00 00 00 00 00 e1 e0 00 02:31:30.777 READ LOG EXT
b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 02:31:30.777 SMART WRITE LOG
b0 00 d5 00 01 00 00 00 c2 4f e0 a0 00 02:31:30.776 SMART READ LOG
3f 00 00 00 01 00 00 00 00 00 e0 e0 00 02:31:30.776 WRITE LOG EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4693 -
# 2 Short offline Completed without error 00% 4669 -
# 3 Short offline Completed without error 00% 4646 -
# 4 Short offline Completed without error 00% 4622 -
# 5 Short offline Completed without error 00% 4598 -
# 6 Short offline Completed without error 00% 4574 -
# 7 Short offline Completed without error 00% 4551 -
# 8 Short offline Completed without error 00% 4527 -
# 9 Short offline Completed without error 00% 4504 -
#10 Short offline Completed without error 00% 4480 -
#11 Short offline Completed without error 00% 4456 -
#12 Short offline Completed without error 00% 4432 -
#13 Short offline Completed without error 00% 4408 -
#14 Short offline Completed without error 00% 4384 -
#15 Short offline Completed without error 00% 4360 -
#16 Short offline Completed without error 00% 4336 -
#17 Short offline Completed without error 00% 4312 -
#18 Short offline Completed without error 00% 4288 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: 32/35 Celsius
Lifetime Min/Max Temperature: 21/36 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/65 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (444)
Index Estimated Time Temperature Celsius
445 2019-06-27 15:47 32 *************
... ..(198 skipped). .. *************
166 2019-06-27 19:06 32 *************
167 2019-06-27 19:07 33 **************
... ..(132 skipped). .. **************
300 2019-06-27 21:20 33 **************
301 2019-06-27 21:21 32 *************
302 2019-06-27 21:22 33 **************
... ..( 53 skipped). .. **************
356 2019-06-27 22:16 33 **************
357 2019-06-27 22:17 32 *************
... ..( 86 skipped). .. *************
444 2019-06-27 23:44 32 *************
SCT Error Recovery Control:
Read: 70 (7,0 seconds)
Write: 70 (7,0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 3261 --- Lifetime Power-On Resets
0x01 0x010 4 4699 --- Power-on Hours
0x01 0x018 6 9958711750 --- Logical Sectors Written
0x01 0x020 6 46290841 --- Number of Write Commands
0x01 0x028 6 125275027868 --- Logical Sectors Read
0x01 0x030 6 496938087 --- Number of Read Commands
0x01 0x038 6 4031498112 --- Date and Time TimeStamp
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 4499 --- Spindle Motor Power-on Hours
0x03 0x010 4 3943 --- Head Flying Hours
0x03 0x018 4 4629 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 0 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors
0x03 0x040 4 115 --- Number of High Priority Unload Events
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 32 --- Current Temperature
0x05 0x010 1 32 --- Average Short Term Temperature
0x05 0x018 1 30 --- Average Long Term Temperature
0x05 0x020 1 36 --- Highest Temperature
0x05 0x028 1 22 --- Lowest Temperature
0x05 0x030 1 34 --- Highest Average Short Term Temperature
0x05 0x038 1 25 --- Lowest Average Short Term Temperature
0x05 0x040 1 30 --- Highest Average Long Term Temperature
0x05 0x048 1 29 --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 65 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 12850 --- Number of Hardware Resets
0x06 0x010 4 6521 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 7 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 133802 Vendor specific
Exitcode: 64 (0x40)
Type <return> to exit: