3dfx on jo eellä

Liittynyt
29.10.2017
Viestejä
72
Melkoisen harvinainen Canopus Pure3D LX (sealed-versio). Tästä LX-versiostahan puuttui tuo "TV-out" ja ehkä siksi tämä jäikin huomattavasti harvinaisemmaksi kuin Canopus:in toinen 6 megan malli.

EDIT: Kuvien valoisuus ja sävyt olivat pielessä - korjattu.









 
Viimeksi muokattu:

aop

Liittynyt
17.10.2016
Viestejä
1 359
Tartteis jostain muutaman Voodoo 3 kortin lisää retrokoneisiin.

Pystyisköhän noihin Velocity 100 kortteihin vaihtamaan muistipiirit isompiin ja flashaamaan Voodoo 3 BIOSin?
 

Hellsinki

Kapteeni pienkonekorjaaja
Liittynyt
28.10.2016
Viestejä
2 110
Tartteis jostain muutaman Voodoo 3 kortin lisää retrokoneisiin.

Pystyisköhän noihin Velocity 100 kortteihin vaihtamaan muistipiirit isompiin ja flashaamaan Voodoo 3 BIOSin?
Facen Retrokonekirppiksellä on Niko syrjälällä myynnissä muutama
 

Subv1sa

Tukijäsen
Liittynyt
17.10.2016
Viestejä
1 107
Löyty tänään ku roskia vein joku vanha koneen raato ni siinähän nörtin mielenkiinto heräs.
Poweri oli rikki mutta varastostahan niitä löytyy.
Koneessa näköjään kiinni celeron 600mhz ja voodoo3 2000.
Oiskohan tosta kakkos retrokoneeks? (mulla yks Pentium 90 retrokone vanhoille dossi peleille)
 
Liittynyt
26.10.2016
Viestejä
423
Löyty tänään ku roskia vein joku vanha koneen raato ni siinähän nörtin mielenkiinto heräs.
Poweri oli rikki mutta varastostahan niitä löytyy.
Koneessa näköjään kiinni celeron 600mhz ja voodoo3 2000.
Oiskohan tosta kakkos retrokoneeks? (mulla yks Pentium 90 retrokone vanhoille dossi peleille)
Ehdottomasti. Tällähän potkii half-lifet yms herkut joita ei tuolla 90 penalla pyöritä! Virtalähde kiinni niin kone on 40-50e arvonen.
 

Subv1sa

Tukijäsen
Liittynyt
17.10.2016
Viestejä
1 107
Ehdottomasti. Tällähän potkii half-lifet yms herkut joita ei tuolla 90 penalla pyöritä! Virtalähde kiinni niin kone on 40-50e arvonen.
Joo junttasin powerin kiinni ja toimii paitsi rossun tuuletin ei toimi.
Täytyy laittaa toikin sit retronurkkaukseen kun siihen joskus vapautuu tilaa :rofl:
 
Liittynyt
26.10.2016
Viestejä
423
Uuh. Bitboys Axe Rev B ilmaantui jälleen itselle. Tämä on jo toinen samanlainen mutta myönnettäköön että sen ensimäisen menin hölmönä vaihtokaupoissa luovuttamaan ja siitä lähtien se kaihersi.

Päätin että tälläinen pitää hommata vielä itselle vaikka tulee olemaankin haastavaa... Loppuviimein se olikin yllättävän helppoa kun tajusin etsiä sieltä mistä muut eivät olleet...

Nyt se tulee omalle seinälle kehyksiin ❤

IMG_20180924_160251.jpg
 

Kaotik

Banhammer
Ylläpidon jäsen
Liittynyt
14.10.2016
Viestejä
21 452
Mihis Bitbois piiri tökkäsi? Rahoitukseenko?
BitBoysin molemmat "kunnon yritykset" tökkäsivät ulkopuolisiin juttuihin, ei niinkään rahoitukseen.
Ensin TriTech jonka kautta Pyramid3D oli tulossa meni nuri jonkun audiopuolen(?) oikeusjutun vuoksi ja myöhemmin sitten tämän Axen kohdalla Infineon sulki eDRAM-tuotantolinjansa, jota Axen piti käyttää
 
Liittynyt
26.10.2016
Viestejä
423
Kävipä niin hassusti että fb retro ryhmästä lähtenyt keskustelu johti siihen että löysin omista voodoo 3 korteista hieman harvinaisemman early production samplen :D

Kortin pcb on päivätty 1199 joka on erittäin varhainen V3:lle. Sen lisäksi AGP lukitus puuttuu ja itse V3 piiri on vanhalla logolla varustettu joita ei retail korteissa ollut.

IMG_20181118_094732__01.jpg
 

KtK

Liittynyt
12.03.2017
Viestejä
423
Mun VooDoo Machinen komponentit :)IMG_20170718_175134.jpgIMG_20170630_163900.jpg


Jäähyt paikalla:IMG_20170718_175516.jpg

Kuvassa myös Athlonin Mobile 2400Mhz Prossa joka teki ihmeitä Voodoo5 5500 Framerateile Socket hyppylanka ylikellotettuna yli 3Ghz.
Käsittämättömiä yli 50% parannuksia tuli peleihin ,mitkä ei periaatteessa ole enää Voodoo 5 heiniä.

Esim. Medal of Honor 1. Pyörii ylikellotetulla Duron 600@900 heikosti ,mutta tällä Athlonin mobile 3000Mhz about ihan sika hyvin. Sama raju Fps nousu tapahtuu Myös vanhalla Star Wars2 : Jedi Knight outcast pelillä.

Itse olen itselleni selittänyt hirveän Boostin johtuvan siitä ,että nämä 3dfx ajan jälkeen tulleet pelit käyttää Transform&Lightningia GPU rautatasolla tai CPU:lla
Ja tämä "ylinopea Athloni" hoitaa sen puolen enemmän kuin hyvin. Ei mene ihan samalla kaavalla ,kuin nykyään puhutut CPU/GPU bottleneckit.

Ja tällä retrokoneella Unreal 1 on komea ja Audigyn äänikortilla kunnon vanhan ajan EAX tuella äänet loksautta nykyisten "generig ALC" käyttäjien leuat sijoiltaan ;)
 
Viimeksi muokattu:
Liittynyt
26.10.2016
Viestejä
423
Mitäs käyttistä ajelet koneella?

Mun VooDoo Machinen komponentit :)


Jäähyt paikalla:

Kuvassa myös Athlonin Mobile 2400Mhz Prossa joka teki ihmeitä Voodoo5 5500 Framerateile Socket hyppylanka ylikellotettuna yli 3Ghz.
Käsittämättömiä yli 50% parannuksia tuli peleihin ,mitkä ei periaatteessa ole enää Voodoo 5 heiniä.

Esim. Medal of Honor 1. Pyörii ylikellotetulla Duron 600@900 heikosti ,mutta tällä Athlonin mobile 3000Mhz about ihan sika hyvin. Sama raju Fps nousu tapahtuu Myös vanhalla Star Wars2 : Jedi Knight outcast pelillä.

Itse olen itselleni selittänyt hirveän Boostin johtuvan siitä ,että nämä 3dfx ajan jälkeen tulleet pelit käyttää Transform&Lightningia GPU rautatasolla tai CPU:lla
Ja tämä "ylinopea Athloni" hoitaa sen puolen enemmän kuin hyvin. Ei mene ihan samalla kaavalla ,kuin nykyään puhutut CPU/GPU bottleneckit.

Ja tällä retrokoneella Unreal 1 on komea ja Audigigyn äänikortilla kunnon vanhan ajan EAX tuella äänet loksautta nykyisten "generig ALC" käyttäjien leuat sijoiltaan ;)
 
Liittynyt
26.10.2016
Viestejä
423
Ei nyt taas 3dfx juttu mutta jäätävän hyvän tekstin löysin kiinalaiselta foorumilta koskien bitboys, tritech, vlsi. Vedin kiinaksi kirjoitetun tekstin translaten läpi ja näyttäisi olevan erittäin hyvin luettavissa joten mielelläni postaan tähän.

· The myth of loss: Bitboys
Bitboys has always been a mystery in the graphics chip industry, and most people think it's just a boring joke. Because there are no specific product releases, there are very few followers. But what I want to say is that there is such a company, and there are indeed some people who want to make something good. Maybe you will ask: How do you know so clearly? Because I used to work for them, in their office in Dallas, I worked for them for nearly a year until the company was close. This work experience gave me a chance to look closely at Bitboys so that I can tell you this true story today.

To understand the history of Bitboys, you have to say that a well-known research group, Future Crew, developed a set of technology called Futrue Crew 3D technology, which can significantly improve the graphics processing power of the computer, and then a series of small The company invested in the development of this technology, Bitboys is one of them, it was established in 1991.

Early stage of business

In the early days, Bitboys relied on developing software for other companies to maintain its development. Although they were extremely disgusted with this line, they could only endure temporarily in order to accumulate funds for development. During this time they never stopped the development of 3D display technology, because this is the driving force for their hard work. During 1993, Future Crew developed Second Reality, a technology that enables the functionality and performance of graphics chips that were not possible at the time.Since then, Bitboys has developed a graphics chip based on this technology.

In the two years of 1993 and 1994, Bitboys mainly engaged in hardware research. In 1995, it cooperated with VLSI, a Finnish silicon technology company, and finally completed its own graphics chip. Later, VLSI introduced Bitboys to Tritech in Singapore, working together for Tritech to develop TR25201 and its successors TR25202, TR25203 and TR25204.


TR25201 Technical Specifications

Pixel fill rate: 50 Mpixels/s
Color depth: 32bit
24bit Z + 1bit stencil
Memory: 32bit SD/SG/EDO DRAM
Memory bandwidth: 800 MB/s
Support for two-line / three-line filtering
Single process can handle multiple textures
T&L engine processing power: 1 million vertices per second
Hardware bump mapping
200MHz RAMDAC


Pyramid 3D

TR25201 is undoubtedly a failed product. Due to too many design bugs, the image it displays is seriously distorted. The main problem is the timing problem. In order to make up for this defect, we have to introduce one modified version. Until TR25204, these problems were completely solved, and additional features were added - a VGA signal processing core was integrated. Pyramid 3D was developed for this reason.

While the Pyramid3D display chip is at a critical stage of development, Tritech is mired in a lawsuit that infringes on patents for audio technology. The prosecution has demanded severe claims, and the results of the judgment have dealt a heavy blow to Tritech. It was forced to close for a while, and the highly promising display chip of Pyramid 3D was the most innocent victim of this lawsuit before it was seen before the consumer. After this incident, Bitboys was once again independent.

facing the future

Later in the development of Pyramid3D, Bitboys and Tritech began to study the graphics architecture of the next generation of embedded memory, but with the collapse of Tritech this project became a bubble. Bitboys began to take up the responsibility of new product development, and began to develop Xba architecture (Xtreme Bandwidth Architecture) and its next-generation graphics chip Glaze3D.

During this time, Bitboys never gave up trying to find a partner, in order to get their support.It has been in contact with companies such as Real3D, Rendition, Creative Labs, ATI, NVIDIA, and Diamond Multimedia, but the results are frustrating.

Initially, Bitboys developed Glaze3D as a high-end product, integrating 9 MB of 512-bit embedded display memory (EDRAM). Glaze3D's core operating frequency is set to 150MHz, with a dual texture mapping unit, the fill rate can reach 600 million pixels / sec, also supports the environment bump map function, has already supported multi-chip design.

At this time, Bitboys got its first financing and partnered with Infeon because it had mastered embedded DRAM technology.

Working for Glaze3D

Due to the small number of employees of Bitboys, and the fact that most of them do not have much experience in developing graphics chips, the development of Glaze3D is very slow. Bitboys needs to improve its design in order to pursue stable product performance, but this is no easy task. The whole package is very complicated, taking into account the pixel pipeline and triangle generation problems, in addition to taking into account other more complex aspects, if the problem is clear, it will be a big headache if it encounters an unclear problem. It is not easy to display the various parts of the chip, such as the improvement of the memory control module is very difficult.

For the long-term consideration, Bitboys also plans to develop a graphics geometry processing chip, code-named Thor, which not only integrates the T&L engine but also supports multi-chip bridging, but this plan can only stay at that time. It was not possible on the drawings because the funds were spent on the Glaze3D.

The development of Glaze3D lasted for several years, during which most of the company's energy was spent on design. Kaj Tuomi converted the C code to VDHL, ready for the same chip synthesis.



New development tools

The synthesis of Glaze3D was done at Infineon's French laboratory, which proved that their idea of using a toolkit to design a graphics chip was successful. For its subsequent product development, Bitboys has been using this tool for development. This set of tools has all the necessary features to allow C programmers to complete a unit design. Code written by C programmers can be automatically converted to VHDL code and synthesized by a toolkit.This tool also accurately simulates always, so it can be used for testing and debugging.However, at this time Bitboys found that its original concept of the first opportunity has become obsolete now, whether it is architecture, function and performance. Need to start all over again?


From Glaze3D to Axe

The new tool suite is a gradual development of Glaze3D, and a working version at the end of 2000 is ready. With the help of this tool kit, the design time of Glaze3D has been shortened by a few months, but there are still several areas for improvement in the market.So part of the module of this chip has returned to the design stage. Thanks to the many changes, Axe was born. It integrates 9-12MB of EDRAM, and the internal memory bus width is increased to 1024bit! ! ! In addition, Matrix AA, programmable vertex shader units have been added to the chip.


Axe technical specifications

Pixel fill rate: 600-800Mpixlels/s
Single flow four textures
Single cycle 2 textures
Matrex AA
12MB EDRAM 1024bit bus
Support for DirectX 8 Vertex Shader 1.1
50M vertex/s
Support dual chip

Axe chip schematic ›

li3YJ5BEYw1GI.jpg


Axe prototype

liE0cYslgCqww.jpg


Another Axe prototype

li5VaW1ZWV9Ao.jpg


Axe development

Bitboys set a crazy timetable for Axe, ready to bring it to market within 6 months. If it is calculated according to this schedule, it will be listed during the Christmas period in 2001, when its name will be set to Avalanche3D (Avalanche 3D). According to the work of its work suite, this timetable should be realistic. This is the first time Bitboys has released a finished silicon chip, and there are still some things to do before it becomes a reality.

Like most chips, bugs are inevitable, and Axe is no exception. Although Bitboys quickly found some bugs and solved them as soon as possible, there are still some bugs that take a few months to prove their existence. However, Bitboys did not have that much time according to its development schedule, which did not take into account these issues. The end of 2001 was getting closer and closer, and Bitboys had even more difficulties.

Infineon is in crisis

At the critical moment of Axe chip development, Infineon, a close ally who had been fighting Bitboys for a long time, was in financial crisis. As DRAM prices continue to fall, Infineon, which specializes in memory products, is losing more and more in this industry, and finally decided to close the production line of embedded DRAM, which is a fatal blow for Bitboys because Axe is also mass-produced on this production line. Losing the production base is tantamount to paying the bottom. This made Bitboys fall into a desperate situation, and the super graphics card Axe lost its ability to impact the retail market. But this graphics accelerator card still produces a small portion, which allows Bitboys to use them to raise funds from venture capitalists and to showcase technology to the industry.

Hammer

As the Axe display chip quietly faded out at the end of 2001, another display chip, Hammer (which is different from AMD Hammer), was put on the agenda of priority development. This is a high-end product that will fully support DirectX9. Bitboys learned the lessons of the past, did a lot of work for this display chip, and found a reliable partner. This new product has undergone major changes, such as full-screen anti-aliasing technology, occlusion culling and memory management. However, there are still many problems that follow.

Hammer technical specifications

Pixel fill rate: 1200Mpixlels/s or more
Single cycle 4 textures
Support DX9 Pixel Shader
Support DX9 Vertex Shader
3MB EDRAM
POC system
MaxtrixAA2
100M vertex/s



By the end of 2001, the shortage of funds had intensified, and Bitboys had made several layoffs, while at the same time it did not give up its efforts to seek venture capital. But by the end of February, the economic situation was still not improving, so Bitboys was laid off again, and I am also on the list of layoffs. As time progressed, more and more people were fired, and even the office in Dallas was closed.

Bitboys is convincing investors in other areas because it is difficult to pull into venture capital using chip technology. Many software development companies have contacted Bitboys, and even several companies almost reached an agreement with Bitboys, but in the end there was no actual transaction.

Biyboys also approached mobile chipset developers and PDA manufacturers, making them believe that their technology is also very useful in this area. It should be said that this step of Bitboys is very sensible, although the benefits of this aspect may not be too much.

New development direction

The work of developing chips for mobile devices has officially begun. Although a single drawing cannot be found, the marked symbols can be found next to the electronic parts.After some hard work, a rough product was quickly completed, and the simulation tool allowed the C code to be output directly from the FPGA simulator, which means that the data can be transformed. The simulation demonstrates the correctness of the chip design.

After the end of the US operation, Bitboys began working with major electronics companies to develop mobile solutions such as PDAs and cell phones. The design of these chips is fundamentally different from the previously developed products. First, the need to save energy should be considered. Second, the smaller the chip, the better. This is a very high requirement for a company that is unconventional. However, in general the challenge will make the work more interesting.

Bitboys quickly took out the draft design and used the toolkit to convert the C source code directly into an FPGA so that Bitboys could do some demonstrations and the results of the demonstration showed extremely high performance.

Bitboys latest mobile chip

liHFRqDkuOnOM.jpg


Using its technology and demo, Bitboys got some contracts. As for the innovation of its technology, I am not sure. Their development is still going on today, and we are expected to see chips using these technologies in the first half of 2003, and a series of products have been launched.

Written at the end

This is Bitboys. Love or hate, they are struggling to struggle. Although they are no longer oriented to high-end 3D graphics chips, they still express their value by entering the mobile space. I don't know if it will come back to the high-end market that it has always dreamed of. After all, it is the first place to survive.
 
Liittynyt
26.10.2016
Viestejä
423
Keräily siirtyi uudelle "levelille" vaikka kuinka olin aiemmin että tähän en lähde ja perus 3dfx kortit riittävät.

No ei ne näemmä riittäneet.

Quantum3D Obsidian2 200SBi saapui joku aika sitten ja nyt hieroskelen kauppoja vielä 200SB kortista.

Näitähän on käytetty lentosimulaattoreissa ja armeijan simulointihommiin. Varmasti myös minta muuta tehtävää näille on keksitty.

IMG_20190201_193758__01.jpg


IMG_20190201_193803__01.jpg
 
Liittynyt
18.10.2016
Viestejä
1 980
Kyllä tuolaista mieluummin kopan lasin läpi katselisi kuin nykyisiä led-viritelmiä ;)
 

KtK

Liittynyt
12.03.2017
Viestejä
423
Innostusin ittekkin pistämään VooDoo 5 masiinan päälle ja sehän alko heti kiukuttelemaan.
Kuva sekasin ja meni palikkaiseksi. Lopulta huomasin ,että Abitin KT7-raidin yks muistien liki oleva konkka oli oksentanut kamat ulos. Vajaa vuos sitten oli kaik päällepäin ok.

Putsauksen jälkeen ei suosunut voodoo 5 käynnistymään ,mutta toinen AGP näyttis GeForce 4 sit taas suostui vaivoin biokseen pari kertaa.

Saa nähdä tuliko Voodoosta seinäkoriste. Lopettaa kyllä melko tehokkaasti retroilun siinä tapauksessa.

Testaamaan pääsen vasta emorempan jälkeen :( Paikalle tulee Epoxin 8k3a+ ,mutta senkin konkat on kans vaihtokamaa. Päädyistä vuotaneet muutamat,muttei emolle.
 
Liittynyt
26.10.2016
Viestejä
423
Ai perhana kuulostaa pahalta. Jos ei lähde niin olehan yhteyksissä niin mietiskellään millä lähtis. Epoxin pitäs olla erittäinkin täydellisesti yhteensopiva vitosen kanssa.

Innostusin ittekkin pistämään VooDoo 5 masiinan päälle ja sehän alko heti kiukuttelemaan.
Kuva sekasin ja meni palikkaiseksi. Lopulta huomasin ,että Abitin KT7-raidin yks muistien liki oleva konkka oli oksentanut kamat ulos. Vajaa vuos sitten oli kaik päällepäin ok.

Putsauksen jälkeen ei suosunut voodoo 5 käynnistymään ,mutta toinen AGP näyttis GeForce 4 sit taas suostui vaivoin biokseen pari kertaa.

Saa nähdä tuliko Voodoosta seinäkoriste. Lopettaa kyllä melko tehokkaasti retroilun siinä tapauksessa.

Testaamaan pääsen vasta emorempan jälkeen :( Paikalle tulee Epoxin 8k3a+ ,mutta senkin konkat on kans vaihtokamaa. Päädyistä vuotaneet muutamat,muttei emolle.
 

KtK

Liittynyt
12.03.2017
Viestejä
423
Ai perhana kuulostaa pahalta. Jos ei lähde niin olehan yhteyksissä niin mietiskellään millä lähtis. Epoxin pitäs olla erittäinkin täydellisesti yhteensopiva vitosen kanssa.
Juuh ,jos vaikka huomenna rupeis kartottamaan tota Epoxin emoa ja juottais konkat irti. Jää odoteltavaksi VooDoon kohtalo.

Siinä käynnistellessä sekoilevaa konetta ,heitin näyttiksen bioksen defaultiksi f2 näppäimellä ja sen jälkeen ei kuvaa tullut kai? vissiin :(

Sekava tilanne,kun ei osannut yhtään odottaa tommosta emolevyn vikaa.

Oli sisällä BIOS ,jolla voi muistiasetuksia ymm säädellä boottivalikosta f1 näppäimen kautta. Tuli mieleen ,että siin sählätessä saattoi mennä bios sekasin jotenkin.

Emon oma bios oli kuin tervassa ,ruudun päivitys kesti sekuntteja.
 
Liittynyt
17.10.2016
Viestejä
3 799
Innostusin ittekkin pistämään VooDoo 5 masiinan päälle ja sehän alko heti kiukuttelemaan.
Kuva sekasin ja meni palikkaiseksi. Lopulta huomasin ,että Abitin KT7-raidin yks muistien liki oleva konkka oli oksentanut kamat ulos. Vajaa vuos sitten oli kaik päällepäin ok.

Putsauksen jälkeen ei suosunut voodoo 5 käynnistymään ,mutta toinen AGP näyttis GeForce 4 sit taas suostui vaivoin biokseen pari kertaa.

Saa nähdä tuliko Voodoosta seinäkoriste. Lopettaa kyllä melko tehokkaasti retroilun siinä tapauksessa.

Testaamaan pääsen vasta emorempan jälkeen :( Paikalle tulee Epoxin 8k3a+ ,mutta senkin konkat on kans vaihtokamaa. Päädyistä vuotaneet muutamat,muttei emolle.
Minua kiinnostaisi ostaa tämä rikkinäinen V5 tai tarjota korjauspalvelua :)
 

KtK

Liittynyt
12.03.2017
Viestejä
423
Yess :) Laitoin riskillä kuivakonkkasen Epoxin emon tulille ja aluksi Pci s3 virgen kanssa. Biokseen pääsi,vaikka core jännitteet heitteli aika tavalla.

Sitten Voodoo 5 ja tuntuu pelaavan ihan ok ,ei grafiikkavirheitä ja säkenöiviä tekstejä.

Mutta emon konkat täytyy vaihtaa ,on ihan kaputt toi Epox 8k3a+ tällä hetkellä. Ei varmaan muuta parempaakaan löydy Voodoo 5 AGP 3.3v kaveriksi.
 
Liittynyt
17.10.2016
Viestejä
3 799
Mulle on tosiaa siunaantunut satsi noita -320 steppingin VSA-100 piirejä ja etsin jotain sopivaa uhria V4/5 maailmasta johon ne voisi tuupata :D

-320 piiri kun on se joka oli suunniteltu V5 6k kortteihin, kellottuu 200MHz saakka aika vaivatta.
 
Liittynyt
26.10.2016
Viestejä
423
Mulle on tosiaa siunaantunut satsi noita -320 steppingin VSA-100 piirejä ja etsin jotain sopivaa uhria V4/5 maailmasta johon ne voisi tuupata :D

-320 piiri kun on se joka oli suunniteltu V5 6k kortteihin, kellottuu 200MHz saakka aika vaivatta.
Juu itsellä on tuo yksi V4 4500 joka päivitelty tappiin eli löytyy tuo 320 sekä 64mb ram

Juuri vaihtelin yhteen neloseen uuden 220 piirin mutta taitaa olla muistivikanen enkä ole vielä ehtinyt etsimään korvaavia.

P.S myytkö yhden 320? :D

IMG_20190203_125051__01__01.jpg


IMG_20190203_125450__01__01.jpg


IMG_20190203_130800__01__01__01.jpg


IMG_20190203_135801__01.jpg


IMG_20190203_133816__01.jpg
 
Liittynyt
17.10.2016
Viestejä
3 799
Vähänhän tuo siltä näyttää joo.

Mulla on just nyt osina yksi V5 5500 mutta siihen en ajatellut 320 piirejä tuhlata kun on muuten suht räpeltämätön kortti.

2019-01-19 20.26.51.jpg

Mukavia juotella nämä lyijyllisen aikakauden ja ei niin järeiden piirilevyjen kortit kun vertaa moderniin rautaan :D

Meni aikansa keksiä riittävän miedot parametrit juotokseen ettei käpristele noita piirejä (infrapuna ylä- ja alapuolelta)

EDIT: nykysestä 320 satsista ei ole vapaita piirejä enää mutta ostin niitä lisääkin kun varmistui että ovat aitoja, seuraavasta riittää kyllä myytäväksi jos joku haluaa.
 
Viimeksi muokattu:
Liittynyt
17.10.2016
Viestejä
3 799
Tommonen V4 4500 noilla päivityksillä rupeaa olemaan jo lähellä vakio V5 5500 nopeuksia peleissä varmaan.
Mikäänhän ei estä tekemästä lähes samaa 5 5500 kortille, siihenkin saa ladottua 128 megaa joskin se vaatii muutaman hyppylangan ja muuta virittelyä :D
 

KtK

Liittynyt
12.03.2017
Viestejä
423
Kuinkahan paljon v5 5500 vakiot VSA-100 gput mahtaa kellottua ,ellei muistit ottaisi vastaan. Luulen ainakin ,että omassa kortissa muistit ekaksi tekee ongelman ,kun on hyvät jäähdytykset gpuille ja ne ei käy kuumana yhtään.

Olisko ollut 174Mhz tiukka raja ittellä. Sen jäkeen tulee pixeleitä graffoihin.

Löysin hyvän testin tosta Alien vs Predator 2 pelistä. Siinä olevista puista viidakossa näkee heti,jos on liikaa kelloja.
 
Liittynyt
17.10.2016
Viestejä
3 799
Kuinkahan paljon v5 5500 vakiot VSA-100 gput mahtaa kellottua ,ellei muistit ottaisi vastaan. Luulen ainakin ,että omassa kortissa muistit ekaksi tekee ongelman ,kun on hyvät jäähdytykset gpuille ja ne ei käy kuumana yhtään.

Olisko ollut 174Mhz tiukka raja ittellä. Sen jäkeen tulee pixeleitä graffoihin.

Löysin hyvän testin tosta Alien vs Predator 2 pelistä. Siinä olevista puista viidakossa näkee heti,jos on liikaa kelloja.
Joo ei ne vakio muistitkaan tuossa apua anna. Omat vakiokuntoisest kortit on järjestään jääneet 170 ja 180 MHz väliin. Toki jollain muulla käy silicon lotteryssä parempi tuuri ja kortti kulkee jopa 190MHz. Pitäsköhän kokeilla joskus extreme jäähdytystä näille? :D

Toisaalta sitten jos muistia haluaa päivittää niin 4ns 16 MB TSOP2 86-pin sdrammitkaan ei ole mitään maailman yleisimpiä lastuja näin vuonna 2019. SERristä olen itse niitä purkanut talteen.
 
Liittynyt
26.10.2016
Viestejä
423
Tuossa mittään riskiä ole, olen jo korkein tarjoaja :D
Kyllä vähän huonot kuvat on että selviäis onko pädit irti tuosta vasemmalta alhaalta. :rolleyes:

Kun ilmossa lukee kuitenkin että new chip chip cannot be installed o_O
 
Liittynyt
17.10.2016
Viestejä
3 799
Kyllä vähän huonot kuvat on että selviäis onko pädit irti tuosta vasemmalta alhaalta. :rolleyes:

Kun ilmossa lukee kuitenkin että new chip chip cannot be installed o_O
Padit on ihan varmasti irti kymmenmäärissä mutta minua ei pelota sekään :D
 
Liittynyt
17.10.2016
Viestejä
3 799
Kyllä mulla on ajatus että siitä ihan vitonen tulisi. On harjoiteltuna jo toisesta korjauksesta prosessi jolla tuo tulee kuntoon :) Nämä harvat ja isopalloiset BGA:t on kesyjä viritellä vaikka miten, hurjin tai kurjin korjaus mihin olen sotkeentunut oli kahden hyppylangan vieminen 0,3mm palloilla olevan bga:n alle sisäriviin :D
 
Liittynyt
26.10.2016
Viestejä
423
Kyllä mulla on ajatus että siitä ihan vitonen tulisi. On harjoiteltuna jo toisesta korjauksesta prosessi jolla tuo tulee kuntoon :) Nämä harvat ja isopalloiset BGA:t on kesyjä viritellä vaikka miten, hurjin tai kurjin korjaus mihin olen sotkeentunut oli kahden hyppylangan vieminen 0,3mm palloilla olevan bga:n alle sisäriviin :D
Eihän sulla satu olemaan paria joutilasta muistia niin pääsis vaihteleen tuohon neloseen?
 

KtK

Liittynyt
12.03.2017
Viestejä
423
Nyt täytyy odottaa uutta VooDoo emolevyä ensi viikkoon.
Abitin KT7-raidi 133 ei enää nappaa kunnostettunakaan ja lahonnut Epoxin 8k3a+ pistettiin paloiksi pois silmistä jätteiden joukkoon.

Nyt on tulossa MSI KT3 Ultra kaikilla lisukkeilla ja ei tarvitte ruveta liian isoilla kolveilla konkkia heti juottamaan.

Kun noissa on valmiina jo kunnon Japanilaiset Rybyconin konkat. Ja toimivat vieläkin ok pääsääntöisesti kuulemma.
En olis aikoinaan uskonut ,mutta MSI on on laadukkaampi kuin lähes kaikki muut emot.
ASUS ilmeisesti (a7v333) myös hyvä ja laadukas vaihtoehto Voodoo korteille ,kun AGP 3.3v on tarpeen.

Tarvii varmaan pistää aluksi toi Voodoo 3 3000 testiin ,se on ollu työttömänä tavallisen kauan.
Varsinkin kun toi sen aikoinaan syrjäyttänyt V5 5500 on myös kehissä.
 
Liittynyt
26.10.2016
Viestejä
423
Kai noi muistit sekasin toimii että ihan kahdellakin varmaan pärjäilis.

Komeeta jälkee :cigar2: laitoit kuitenkin uuden VSA:n varmaan kun parit pädit uupu sieltäkin.

Tuo pari viestiä ylempänä ollut vitonen tuli laitettua kuntoon. 15 vuotta sitten itse särjin ja nyt sitten näin






Jotain saattaa olla, mitä tarvisit ja paljonko
.
 
Liittynyt
18.10.2016
Viestejä
702
@Kizmo
Onko tietoa, että saako tuota Amtechin fluxia jostain järkevään hintaan postikulujen osalta?
Entä oletko testannut, että tekeekö halvoilla kiinafluxeilla mitään?

Jotta ei mene ihan ohi aiheen niin onhan noita romuja minullakin, muttei mitään harvinaisuuksia.
Yksi Voodoo ykkönen ja ainakin pari PCI-väyläistä Voodoo 3 2000-tuhnua. Toiseen vaihdettu "huvin vuoksi" tantaalit elkojen tilalle, joten pitäisi toimia maailman tappiin ainakin konkkien osalta.
Saattoi joku Bansheen romukin jossain lojua tai sitten olen nähnyt unta.
Käyttöä en ole vielä noille keksinyt, mutta pitänee jossain vaiheessa testata Interstatea kun en ole sitä koskaan 3dfx:n kera pelannut.
 
Liittynyt
26.10.2016
Viestejä
423
Advanced Professional Solder Soldering Paste RMA-223 10CC Flux Gel Welding Oil M | eBay

Tuolta lähtee.

Ehdottomasti kaikki 3dfx kortit esiin ja puunaat kuntoon. Älä jätä romukoppaan mitään :cigar2:

@Kizmo
Onko tietoa, että saako tuota Amtechin fluxia jostain järkevään hintaan postikulujen osalta?
Entä oletko testannut, että tekeekö halvoilla kiinafluxeilla mitään?

Jotta ei mene ihan ohi aiheen niin onhan noita romuja minullakin, muttei mitään harvinaisuuksia.
Yksi Voodoo ykkönen ja ainakin pari PCI-väyläistä Voodoo 3 2000-tuhnua. Toiseen vaihdettu "huvin vuoksi" tantaalit elkojen tilalle, joten pitäisi toimia maailman tappiin ainakin konkkien osalta.
Saattoi joku Bansheen romukin jossain lojua tai sitten olen nähnyt unta.
Käyttöä en ole vielä noille keksinyt, mutta pitänee jossain vaiheessa testata Interstatea kun en ole sitä koskaan 3dfx:n kera pelannut.
 
Toggle Sidebar

Statistiikka

Viestiketjut
237 489
Viestejä
4 164 022
Jäsenet
70 415
Uusin jäsen
Toivokipina

Hinta.fi

Ylös Bottom